Log in to use our free company, program and sector update tracker feature.

Front page

Northrop Grumman and Bell Helicopter are currently completing vehicle modifications and conducting preliminary "power on" activities on the new Fire-X medium-range vertical unmanned aerial system. Work is underway at Bell's Xworx rapid prototyping facility in Fort Worth, Texas.

Northrop Grumman, Bell Helicopter conduct first "Power-On" of new Fire-X medium-range vertical unmanned system

Northrop Grumman Corporation (NYSE:NOC) and Bell Helicopter, a Textron company (NYSE:TXT), have moved a significant step closer to being able to offer military users a vertical unmanned system that can ferry cargo – either internally or externally – over extended distances.

On Sept. 17, the team applied external power for the first time to the main computers and associated subsystems for its new Fire-X medium-range vertical unmanned aerial system (VUAS), currently in final integration and test at Bell Helicopter's Xworx rapid prototyping facility in Fort Worth, Texas.

First flight for the new extended range, cargo-hauling VUAS, which is based on the FAA-certified Bell 407 airframe, is expected by the end of CY2010.

"The Fire-X 'power-on' sequence, which validates the integrity of the electrical system, went exactly as planned," said George Spongberg, Northrop Grumman's Fire-X program manager. "It confirmed that the air vehicle's vehicle management system has been configured properly, and that all of the air vehicle's new wire harnesses are delivering power at the right levels to all of the major subsystems."

Fire-X's new wire harnesses were produced, tested and installed by Bell Helicopter, he added.

The power-on event follows four months of Fire-X vehicle modifications at Xworx to convert a commercial Bell 407 from a piloted vehicle into an unmanned or optionally piloted vehicle. The modifications included not only removal of non-mission-essential equipment such as seats and sound insulation, but also installation of new wire harnesses and avionics required to control the vehicle in an unmanned configuration.

"The challenge," explains Spongberg, "is to duplicate, using hardware and software, the behavior of the air vehicle when it is flown by a human. For example, we're installing and testing actuators that will move the air vehicle's flight control surfaces in response to commands from a ground control station the same way they would move in response to commands from a pilot in the cockpit."

The team is also installing and validating the software that will perform critical guidance, navigation and control (GN&C) functions for the new system, he added.

Over the next month, the Northrop Grumman/Bell Fire-X team expects to conduct preliminary flights of the air vehicle in Fort Worth in a manned configuration to validate its GN&C system, then convert it back to an unmanned system. After completion of ground testing and engine runs, the air vehicle will be ferried, in an optionally piloted configuration, to the U.S. Army's Yuma Proving Ground, Ariz. for final testing before Fire-X's first demonstration flight in an unmanned configuration.

Fire-X is a fully autonomous, four-blade, single-engine unmanned helicopter that combines the best of two proven air systems in a low cost, fast-fielding package: the versatile reconnaissance, surveillance and target acquisition architecture of the U.S. Navy's MQ-8B Fire Scout vertical takeoff and landing tactical UAV, and the extended range, payload and cargo hauling capabilities of the commercially mature Bell 407 helicopter.

Fire-X offers commanders a useful load of more than 3,000 pounds – for fuel, payloads and/or cargo. That load can typically support intelligence, surveillance and reconnaissance missions up to 16 hours long, or cargo missions of 2,500 pounds out to a range of 110 nautical miles.

Press release issued by Northrop Grumman Aerospace Systems on September 28, 2010


 Contact details from our directory:
Northrop Grumman Aerospace Systems Airframer
Bell Helicopter Textron Airframer


 Related aircraft programs:
Bell 407


 Related directory sectors:
Airframe Assemblies

Enhanced listings:

Reduce the time spent on current projects by using ESDU – engineering data and software that have been approved and endorsed by professional institutions.

Quintus Technologies
Quintus Technologies is a global leading provider of high pressure fluid cell presses and hydroform deep-draw presses for sheet metal forming

Victrex Plc
New VICTREX® AE250 composites and hybrid molding technology are changing the equation in Aerospace composites – find out more!

USA Borescopes
USA Borescopes is a global supplier of world class visual inspection equipment. We are the one stop source for aviation professionals.

MW Industries, Inc
Design and manufacture springs, fasteners and related products for aerospace including: engine components, flight controls, propulsion, landing gear, interiors, avionics, and space exploration vehicles.

See our advertising tariff.


Monthly page limit exceeded. Please buy a subscription.

© Copyright of Airframer Limited, operated under licence by Stansted News Limited 2016. Terms & Conditions of reading.