Log in to use our free company, program and sector update tracker feature.

Front page

Wake turbulence during cruising flight

When aircraft fly, they generate turbulent airflow behind them known as 'wake turbulence', which can affect following air traffic. The German Aerospace Center (Deutsches Zentrum fuer Luft- und Raumfahrt; DLR) has developed a method to measure wake turbulence in flight. This method was put to the test during flights with DLR's Falcon 20E research aircraft.

When assessing wake turbulence during cruising flight, it is particularly important to measure the strength and intensity of the vortices and the behaviour of an aircraft flying into wake turbulence. As cruising flight takes place at altitudes of over 10,000 metres, it is impossible to carry out such analyses from the ground.

Measurement campaign behind large aircraft

For the test flights, DLR researchers flew through the airspace above Mecklenburg-Western Pomerania and Brandenburg as often as possible and through the centre of the wake turbulence caused by typical airliners. "This was a very complex undertaking. It placed high physical requirements on the test team and the test aircraft," said Dietrich Fischenberg, a researcher in the DLR Institute of Flight Systems in Braunschweig. "An essential element was good collaboration between all participants: the DLR Institutes of Flight Systems and Atmospheric Physics, the DLR Flight Experiments department, German air traffic control (Deutsche Flugsicherung; DFS) and, last but not least, the pilots who permitted us to fly through and measure the wake turbulence," Fischenberg continues. A DLR staff member working with DFS during the tests put together a real-time selection of potential aircraft in the test zone, and air traffic controllers informed the relevant pilots of the tests taking place. They then asked for important flight data needed for the research and brought the Falcon closer to the airliner. Two hundred tests were carried out in wake turbulence at ranges from five up to a maximum of 25 nautical miles behind the airliners.

Information on wake turbulence for new types of aircraft as well

The data collected is now being assessed using software developed by DLR. Researchers are now gaining insights into the strength of the wake turbulence at varying distances behind an aircraft, even at great altitudes. Furthermore, they can determine what happens when the turbulence behind the aircraft sinks and at what point it is safe for other aircraft to fly through the wake turbulence. This new method is also being used to gather information on the flight dynamics of and loads generated on the approaching aircraft.

The strength of the turbulence after it has sunk is currently of particular interest. It allows assessment of the effect that sinking wake turbulence has on aircraft flying at narrow vertical separations in advance. There is something else that this new method can help with; when integrated into the certification process for new, very large aircraft, it might be possible to accurately determine when and where it is safe to fly through the as-yet undetermined wake turbulence. "That is still a long way off, but it would greatly simplify the certification process for new aircraft," says Fischenberg.

Press release issued by DLR - German Aerospace Center on June 6, 2011


 Contact details from our directory:
DLR - German Aerospace Center Fuel Cells, Testing Services, Research/Consulting Services, Composite Design Consultants, Flight Simulators, Instrument Landing Systems


 Related directory sectors:
Test Services

Enhanced listings:

Valence Surface Technologies
The leading metal processing company serving the global aerospace industry. Valence’s ten facilities offer full-service capabilities: NDT, shot peen, chemical processing, paint, and other coatings.

Reduce the time spent on current projects by using ESDU – engineering data and software that have been approved and endorsed by professional institutions.

Beckwood Press
Your single source for aerospace forming equipment. Manufacturer of Triform Sheet hydroforming presses.

Belden Universal
Specialty universal joints and drive shafts, designed to satisfy even the most rigorous operating criteria. Belden Universal is AS9100C certified.

MW Industries, Inc
Design and manufacture springs, fasteners and related products for aerospace including: engine components, flight controls, propulsion, landing gear, interiors, avionics, and space exploration vehicles.

See our advertising tariff.


data pages remaining in monthly quota for non-subscribers

© Copyright of Airframer Limited, operated under licence by Stansted News Limited 2016. Terms & Conditions of reading.