Log in to use our free company, program and sector update tracker feature.

Front page

Sikorsky tests CH-53K helicopter for airframe structural strength

Sikorsky Aircraft Corp., a subsidiary of United Technologies Corp., has successfully completed an initial series of tests required by the Naval Air Systems Command to verify the structural strength of the CH-53K heavy lift helicopter. Conducted on a full-size non-flying airframe called the Static Test Article, the tests are part of a three-year program to validate that the largest helicopter ever designed and built by Sikorsky has the structural integrity to operate safely over its entire flight envelope — from its empty gross weight of 44,000 pounds up to its maximum gross weight of 88,000 pounds with external load.

"The Static Test Article will enable Sikorsky to replicate the many stresses, strains and aerodynamic forces the CH-53K helicopter will experience during all aspects of flight, whether the aircraft is empty, filled with cargo, or carrying up to 36,000 pounds of gear suspended beneath the aircraft by an external sling," said Mike Torok Sikorsky's CH-53K Program Vice President. "By placing incrementally heavier static loads on various parts of the airframe assembly — including those well beyond the airframe's analytical design strength — we can measure structural integrity, airworthiness and crash worthiness, and verify safety margins for all expected operational conditions."

The Static Test Article is housed in a specially-built test facility at Sikorsky's manufacturing plant in Stratford, Conn. Consisting of the cockpit, the cabin, fuel sponsons, a transition section and the tail rotor pylon, the complete airframe assembly is suspended off the ground by the shaft of its main rotor gearbox. Surrounding support beams hold the numerous hydraulic cylinders that apply the flight and inertial loads to parts of the airframe assembly. Also attached to the STA structure are component-representative weights that simulate the presence of the engines and landing gear, among other key subsystems and components.

To date, Sikorsky has completed a total of six test conditions on the Static Test Article, all conducted during 2013 and early 2014. The first four test conditions satisfy pre-flight requirements ahead of a CH-53K flight test aircraft taking to the skies for the first time later this year. Replicating the maximum load conditions encountered while in flight, the four pre-flight tests measured the structural strength of the tail rotor pylon during high and low speed flight maneuvers, the landing gear during impact with the ground, and the full airframe structure while under maximum rotor power.

Sikorsky will continue to test the structural integrity of the CH-53K Static Test Article for another two years to validate the effects of aerodynamic forces and weight distribution on different sections of the airframe.

The Static Test Article is the first of two non-flying CH-53K test articles — along with five prototype and four production-representative heavy lift helicopters — that Sikorsky is developing as part of a $3.8 billion System Development and Demonstration (SDD) contract for the U.S. Navy.

Per the current program of record, the Marine intends to order 200 CH-53K production aircraft, and to stand up eight operational squadrons and one training squadron to support the Marine Corps' operational requirements. Eventual production quantities would be determined year-by-year over the life of the program based on funding allocations set by Congress and the U.S. Department of Defense acquisition priorities.

Press release issued by Sikorsky, a Lockheed Martin company on April 11, 2014


 Contact details from our directory:
Sikorsky, a Lockheed Martin company Airframer


 Related aircraft programs:
Sikorsky CH-53


 Related directory sectors:
Rotors & Propellers

Enhanced listings:

Ascent Aerospace
Ascent Aerospace is the leading provider of aerospace tooling systems, assembly automation and factory integration.

Valence Surface Technologies
The leading metal processing company serving the global aerospace industry. Valence’s ten facilities offer full-service capabilities: NDT, shot peen, chemical processing, paint, and other coatings.

Reduce the time spent on current projects by using ESDU – engineering data and software that have been approved and endorsed by professional institutions.

Belden Universal
Specialty universal joints and drive shafts, designed to satisfy even the most rigorous operating criteria. Belden Universal is AS9100C certified.

Dexmet Corporation
Dexmet MicroGrid® an innovative product line that help improve the composite aircraft withstand the rigors of a lightning strike

See our advertising tariff.


data pages remaining in monthly quota for non-subscribers

© Copyright of Airframer Limited, operated under licence by Stansted News Limited 2016. Terms & Conditions of reading.